close
Long Range Hunting Online Magazine


Go Back   Long Range Hunting Online Magazine > Rifles, Reloading, Optics, Equipment > Reloading

Reloading Berger Bullets

Reply

Brass specs and info

LinkBack Thread Tools Display Modes
  #1  
Unread 07-23-2009, 08:46 AM
Junior Member
 
Join Date: Mar 2009
Posts: 19
Brass specs and info

Looking for information about the specs on brass. re: primers pockets (lg & sm) rifles. Not sure. But, I have found depth range is ( .128 - .132 lg)? And info on the flash hole dia for both lg and sm rifles.

I am working on a Rem 700 30-06. Most of the brass is used and some new has so much difference re: (weight, length, primer pocket, flash hole) Norma, Win, Rem brass so far.

Any ideas about the the depth of the primer below the face of the brass.

Starting to work with 6.284 rounds also if anyone has any info on this round any and all help!

God Speed diamondmfarms

Last edited by diamondmfarms; 07-24-2009 at 07:08 AM.
Reply With Quote
  •   #2  
    Unread 07-23-2009, 09:58 AM
    Platinum Member
     
    Join Date: Aug 2003
    Location: NC, oceanfront
    Posts: 4,061
    Re: Brass specs and info

    GOOGLE 'saami primer specs'

    All I can say about a 6/284 is that you're not gonna be working with buckets of used brass for this one.
    Reply With Quote

      #3  
    Unread 07-23-2009, 10:59 PM
    Silver Member
     
    Join Date: May 2008
    Location: Ohio
    Posts: 248
    Re: Brass specs and info

    here, this might help:


    Primers And Pressure
    Reply With Quote
      #4  
    Unread 07-24-2009, 07:06 AM
    Junior Member
     
    Join Date: Mar 2009
    Posts: 19
    Re: Brass specs and info

    Thanks lever-hed

    Nice info !
    Reply With Quote
      #5  
    Unread 07-24-2009, 02:47 PM
    Platinum Member
     
    Join Date: Aug 2003
    Location: NC, oceanfront
    Posts: 4,061
    Re: Brass specs and info

    Undiscussed by Mr. Calhoon is reliability.
    I have finally reached a conclusion that in small primers, CCIs are not reliable at all.
    They are just too difficult to set off with anything less than perfect conditions.

    I get failures in 223 & 6br with new brass with headspace exceeding .0015", temps drop below 50deg, primers seated with under 4thou crush, or a slightly weaker strike due to bolt under/over-travel.

    The fix has been Federal and Winchester primers. Everytime.
    I set them at exactly 2thou crush(right where they should be).
    Reply With Quote
      #6  
    Unread 07-28-2009, 04:56 AM
    JLM JLM is offline
    Junior Member
     
    Join Date: Jan 2009
    Location: WY
    Posts: 20
    Re: Brass specs and info

    Mike, I'm told the CCI's have harder cups, so you might want to look at switching if you are having problems with light striking.
    Reply With Quote
    Reply

    Bookmarks

    Thread Tools
    Display Modes


    Similar Threads for: Brass specs and info
    Thread Thread Starter Forum Replies Last Post
    I'm new and need help w/ specs on a rifle Kalle "Cully" Hyrkas Rifles, Bullets, Barrels & Ballistics 6 10-11-2010 06:35 PM
    Torque Specs piutemike The Basics, Starting Out 2 01-15-2008 11:23 AM
    338 Lupa Imp. fire form load info & specs on new big 338 wildcat Reloading 9 10-14-2006 07:13 PM
    Specs for a 338 RUM NotEnoughTriggerTime Rifles, Bullets, Barrels & Ballistics 1 12-29-2004 10:42 PM
    Any info on the Federal U'mag brass? Jay, Idaho Rifles, Bullets, Barrels & Ballistics 3 05-01-2004 03:20 PM


    All times are GMT -5. The time now is 02:24 PM.


    Powered by vBulletin ©2000 - 2017, Jelsoft Enterprises Ltd.
    Content Management Powered by vBadvanced CMPS
    All content ©2010-2015 Long Range Hunting, LLC