close
Long Range Hunting Online Magazine


Go Back   Long Range Hunting Online Magazine > Rifles, Reloading, Optics, Equipment > Reloading

Reloading Berger Bullets

Reply

300 WM loading data, Barnes and Berger?

LinkBack Thread Tools Display Modes
  #1  
Unread 09-26-2011, 12:58 AM
Junior Member
 
Join Date: Sep 2011
Location: Virginia
Posts: 4
300 WM loading data, Barnes and Berger?

Does anyone have some loading data 300 Win Mag, Barnes 168 TTSX and Berger 175 and 190 VLD hunting bullets?

I have a healthy supply of IMR-4350 (preferred), and some IMR-4831, and IMR-7828.

Does anyone have a Barnes manual that they can provide the low and high charges and approx. fps?

Anyone know where I can find some Berger reloading data?

Thanks!
Reply With Quote
  •   #2  
    Unread 09-26-2011, 02:22 AM
    Bronze Member
     
    Join Date: Aug 2011
    Location: Townsend MT
    Posts: 70
    Re: 300 WM loading data, Barnes and Berger?

    I'd be interested in the TTSX 168 300wm load data as well. gonna build some up for my mulie draw tag(it's an almost impossible draw) just in case one jumps up a little too close for the edge I'm having built, which also needs to get done in time! Gonna start with rl22 77-80gns, hopin 80 doesn't show too much pressure and keeps accuracy(looks like its on the high end), wanna get it as fast and flat as I can since its just a point and shoot setup. if it passess pressure test i'll probably load up some at 80 and see how well the gun(sako finnbear) likes em. will start at .050 off the lands, hoping its gonna be that simple since most of my time is gonna be burned up getting the edge figured out, not too confident on how well I can do that one, guess I'll see, my first endeavor into the WAY out there stuff, but the 168 TTSX's are gonna be there for backup inside 400 yds and a rush if need be.
    Reply With Quote

      #3  
    Unread 09-26-2011, 06:49 AM
    Bronze Member
     
    Join Date: Jan 2007
    Location: Lockport, N.Y.
    Posts: 55
    Re: 300 WM loading data, Barnes and Berger?

    I load 70.5 gr 4350 with rem9 1/2m primer with barnes tsx168s I get a little over 3100fps and can shoot 3/4 inch at 100yds with a factory savage weather warrior with the accustock and accubrake
    Reply With Quote
      #4  
    Unread 09-26-2011, 11:05 AM
    Silver Member
     
    Join Date: Oct 2006
    Location: White Mountains, AZ
    Posts: 287
    Re: 300 WM loading data, Barnes and Berger?

    Here is the data from Berger:

    300 Winchester Magnum (COAL - 3.340"; Barrel Length - 26")

    Bullet
    Powder
    Start Load
    Approximate Start Velocity
    Max Load
    Approximate Max Velocity
    Fill Ratio


    168 Grain
    IMR 4350
    66.5
    2971
    70.0
    3110
    91.4%

    168 Grain
    IMR 4831
    68.5
    2930
    72.0
    3064
    93.5%
    __________________
    Watch your thoughts; they become words.
    Watch your words; they become actions.
    Watch your actions; they become habits.
    Watch your habits; they become character.
    Watch your character; it becomes your destiny.
    --Frank Outlaw
    Reply With Quote
      #5  
    Unread 09-26-2011, 11:53 AM
    Platinum Member
     
    Join Date: Jan 2011
    Posts: 2,206
    Re: 300 WM loading data, Barnes and Berger?

    I have used as much as 75.5grns of Imr 4350 under a 168 and 74 under a 178 but these loads were not at 3.34", the 168 was 3.450" and the 178 was 3.486" or jammed .005" however both are very accurate. Id start with about 69grns under the 190 .010" off the lands and you may start seeing pressure at 72.5 and that will get you about 3025fps from a 26" barrrel, do not do this in hornady brass it will not take it, it will show pressure signs way to early. I also do not reccoment the ttsx as it may go straight through and you may end up following a long blood trail with no luck, its happened to me, id use the 168 NBT or Amax. The amaxes are devastating at all ranges. Btw imo 4350 and H4831 are the best powders for a 300wm period.
    Reply With Quote
      #6  
    Unread 09-26-2011, 02:46 PM
    Platinum Member
     
    Join Date: May 2009
    Location: Sweet, Idaho
    Posts: 1,135
    Re: 300 WM loading data, Barnes and Berger?

    John, my ruger shoots pinholes with 71.0 grains of IMR 4831 with the 190 berger hunting VLD. 26 inch pac nor barrel has em going at 2943.

    Randy
    __________________
    "Every man has a purpose---------mine is to be behind a rifle.........."

    "I'd rather wake up in the middle of nowhere than be in any city on earth." ---Steve McQueen
    Reply With Quote
      #7  
    Unread 09-29-2011, 09:25 PM
    Bronze Member
     
    Join Date: Aug 2011
    Location: Townsend MT
    Posts: 70
    Re: 300 WM loading data, Barnes and Berger?

    so far this is what i got
    RL22
    TTSX 168
    80 grns was too much pressure, had to drop down to 78 to make the ejector marks go away loaded em .050 off the lands and had fliers. Dropped the load to 77grns and heading back to the range tomorrow to see if they will cooperate a little better still at .050 off the lands. If that doesn't get it I'm gonna load em .075 off the lands and jump the charge back up to 78 n see if that makes it all better.
    Reply With Quote
    Reply

    Bookmarks

    Thread Tools
    Display Modes


    Similar Threads for: 300 WM loading data, Barnes and Berger?
    Thread Thread Starter Forum Replies Last Post
    does anyone have loading data for 243 berger bullets? telkev Reloading 5 06-07-2007 02:26 PM
    Loading Data Slopeshunter Reloading 4 04-15-2007 03:07 AM
    Loading Barnes Triple Shock bonesan Reloading 20 01-24-2007 11:58 PM
    7mm RUM Loading Data keeter Rifles, Bullets, Barrels & Ballistics 3 12-13-2004 12:09 AM
    Loading data for Barnes TXS (.306/168gr) Sebastian_Urban Long Range Hunting & Shooting 4 05-22-2004 09:16 PM


    All times are GMT -5. The time now is 12:20 AM.


    Powered by vBulletin ©2000 - 2017, Jelsoft Enterprises Ltd.
    Content Management Powered by vBadvanced CMPS
    All content ©2010-2015 Long Range Hunting, LLC