Long Range Hunting Online Magazine


Go Back   Long Range Hunting Online Magazine > Rifles, Reloading, Optics, Equipment > Reloading

Reloading Techniques For Reloading


Reply

270 WBM brass from 7mm WBM Rem brass

 
LinkBack Thread Tools Display Modes
  #8  
Old 02-10-2006, 04:56 PM
Silver Member
 
Join Date: May 2005
Posts: 132
Re: 270 WBM brass from 7mm WBM Rem brass

Jim,

Sent you a private email.

300winnie
Reply With Quote
  #9  
Old 02-10-2006, 04:56 PM
Silver Member
 
Join Date: Jan 2006
Location: Oregon
Posts: 317
Re: 270 WBM brass from 7mm WBM Rem brass

I found 7mm wby mag brass made by remington new if anyone wants the web site let me know $23 for 50 ct.
this is what I use in my 270 wby
Reply With Quote
  #10  
Old 02-11-2006, 11:38 PM
Silver Member
 
Join Date: Jan 2006
Location: Oregon
Posts: 317
Re: 270 WBM brass from 7mm WBM Rem brass

can anyone tell me what o.a.l. works best for you with the 270 wby? thanks
Reply With Quote
  #11  
Old 02-12-2006, 12:03 AM
Silver Member
 
Join Date: Jan 2005
Posts: 252
Re: 270 WBM brass from 7mm WBM Rem brass

I just hang em out as far as the clip will handle. My favorite load is swift a frames which are real stubby. So in effect they are probably alot close to the rifling than if I loaded a plastic tipped bullet.
There could easily be .100" difference between the ogive on the a-frame vrs say a accubond so oal doesn't mean much...you just have to experiement....but I do start by hanging them out. If you are dead set on using a certain bullet and don't get the desired accuracy probably try going back about .050" from using all you clip room and see if there is a difference.
Reply With Quote
  #12  
Old 02-19-2006, 03:38 PM
Junior Member
 
Join Date: Jan 2006
Posts: 13
Re: 270 WBM brass from 7mm WBM Rem brass

300 winnie- I was wondering I could impose on your .270/7mm resizing procedure?e-mail- dave.dmjhwk@gmail.com .My cases have been run through the .270 w/m die,I ran them through twice as the top of the
shoulder didn't get pushed back- and they didn't chamber. Ajusted the die down a turn , and now, the first half of each radius is very evident, and they chamber(I did each one, with two strokes on the second run-turning the shell
180 deg between strokes.
Thanks -
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes


Similar Threads for: 270 WBM brass from 7mm WBM Rem brass
Thread Thread Starter Forum Replies Last Post
338 Lapua Brass compared to 300 Remington Ultra Brass DANTEC Rifles, Bullets, Barrels and Ballistics 6 02-29-2012 11:43 PM
Group differences in Weatherby Brass versus new Norma Brass TX mountain hunter Long Range Hunting & Shooting 5 12-29-2010 10:17 PM
25-06 reloading dies, brass, and bullets / 45ACP brass jeffro Reloading Equipment and Components 1 05-01-2010 10:51 AM
338 Edge, Brass life test. Rem 300RUM brass AJ Peacock Reloading 15 12-30-2009 12:26 PM
Nosler Brass cosmetic seconds good brass? sambo3006 Reloading 6 01-04-2007 08:57 PM

Current Poll
Do you watch outdoor shows live or by recording them?
Always recorded - 14.11%
102 Votes
Mostly recorded - 24.20%
175 Votes
Sometimes recorded - 13.42%
97 Votes
Rarely or never recorded - 48.27%
349 Votes
Total Votes: 723
You may not vote on this poll.

All times are GMT -5. The time now is 11:23 PM.


Powered by vBulletin ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Management Powered by vBadvanced CMPS
All content ©2010-2014 Long Range Hunting, LLC