Long Range Hunting Online Magazine


Go Back   Long Range Hunting Online Magazine > Rifles, Reloading, Optics, Equipment > Reloading

Reloading Techniques For Reloading


Reply

25-06 AI fireforming...

 
LinkBack Thread Tools Display Modes
  #1  
Old 06-10-2012, 08:51 AM
Platinum Member
 
Join Date: Feb 2011
Location: Cincinnati, Ohio
Posts: 1,785
25-06 AI fireforming...

Whats the best way to fireform casings for a 25-06AI..? Ive even read about taking loaded 25-06 ammo and firing it in the AI chamber..? But wow...it just dont sound right to me. Whats headspace going to be with that HUGE difference in shoulders...etc.

Anyway, if you have a good method of fireforming Id sure like to hear it.

Sully
Reply With Quote
  #2  
Old 06-10-2012, 10:17 AM
Platinum Member
 
Join Date: Jan 2011
Posts: 2,094
Re: 25-06 AI fireforming...

That is the correct way, in an ackley chamber the standard ammo you're firing headspaces at the neck/shoulder junction with a slight crush fit about .004-.006" and a good bit of resistance when closing the bolt. The best result come from a 57-59k psi load with the bullet touching the lands, that gives it a tad more stability in the chamber. PO Ackleys designs were meant to be able to safely fire factory ammo if you need to or to just form cases.
Reply With Quote
  #3  
Old 06-10-2012, 10:26 AM
Platinum Member
 
Join Date: Feb 2011
Location: Cincinnati, Ohio
Posts: 1,785
Re: 25-06 AI fireforming...

Quote:
Originally Posted by backwoods83 View Post
That is the correct way, in an ackley chamber the standard ammo you're firing headspaces at the neck/shoulder junction with a slight crush fit about .004-.006" and a good bit of resistance when closing the bolt. The best result come from a 57-59k psi load with the bullet touching the lands, that gives it a tad more stability in the chamber. PO Ackleys designs were meant to be able to safely fire factory ammo if you need to or to just form cases.
I got ya. Okie Doke! But you can see I think why it "appeared" to be incorrect.
Thanks
Reply With Quote
  #4  
Old 06-10-2012, 10:38 AM
Bronze Member
 
Join Date: Jul 2011
Location: manitoba, canada
Posts: 80
Re: 25-06 AI fireforming...

hey there,

i know it may not sound right but firing factory 25-06 ammo in the ackley chamber is how you do it... in fact, and correct me if i'm wrong, Ackley specifically designed the AI chambers so that they would fire the factory parent cases safely incase the owner ran out of fireformed brass.... if the owner was out on a hunting trip and lost or ran out of loaded AI ammo they could go down to the store and buy some factory for it...


if the chamber was headspaced correctly the factory ammo should still contact the front of the chamber high on the shoulder near the neck junction...

that being said i have had some factory ammo ( I think it was winchester,) that was at the very low end of headspace specs and the rounds would kinda slump in the chamber and when it fireformed it had a bulge on one side of the case because the case wasnt sitting concentric in the chamber...

now as far as my steps for fireforming go... I decided i wanted to use lapua brass in mine and lapua doesnt make 25-06 so i am stuck neck sizing down from 30-06 brass...

step 1: run 30-06 brass through thandard 25-06 die leaving the last ~ 10 thou of the neck unsized to create a false shoulder to make sure i get a real good seal at the neck shoulder junction

step 2: trim the newly formed 25-06 brass to standard length

step 3: turn the necks to 12 thou thick (probably not needed as i dont have a tight chamber but i do it any way to make them all uniform)

step 4: load with a bullet and powder of your choice at the high end of standard 25-06 load recommendations as per your favorite manual's recommendations for said bullet and powder and fire away... i use 90gr sierra hp with reloader 19.... absolutely insane gopher destruction while fireforming cant be beat!
(lots of other guys will use a cream of wheat technique to fire form using really fast burning pistol powders, i have never tried it but you should be able to search and find lots of info on this sight about it)

step 5: inspect all the cases for split necks etc (never had one with the lapua brass so far) then i neck turn them to shave off any lopsidedness in the necks (once side of the wall thicker than the other) again and make sure i make a slight cut into the shoulder to help remove excess brass from the neck shoulder junction to prevent the formation of the dreaded "donut".... (search donut as related to fireforming ackley brass and you'll get a lot of info and opinions on the topic)

Step 6: work up a load... mine like 115 berger vld and reloader 25....



now if you don't wanna go through all that to work, i'm sure you will be able to make the thing shoot starting with factory 25-06 ammo and remove steps 1-4 of my process...

good luck

orch
Reply With Quote
  #5  
Old 06-10-2012, 10:45 AM
Junior Member
 
Join Date: Jan 2011
Posts: 7
Re: 25-06 AI fireforming...

This may seem obvious, but watch those bolt lugs for galling . Sometimes the chamber is tight and you can have problems with factory ammo. I mention this because I have experienced it. Good luck , the 25-06 A.I. is one of my favorites.
Reply With Quote
  #6  
Old 06-10-2012, 11:20 AM
Platinum Member
 
Join Date: Feb 2011
Location: Cincinnati, Ohio
Posts: 1,785
Re: 25-06 AI fireforming...

orch: Much appreciated. I think I'll start with factory 25-06 ammo in the beginning and then move to Lapua casings. A couple of boxes of factory stuff and 100 casings will last me a LONG time.

Thanks again.

BTW...I think I'll fire real bullets instead of breakfast cereal....*S*
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes


Similar Threads for: 25-06 AI fireforming...
Thread Thread Starter Forum Replies Last Post
6.5-06 AI Fireforming bholtmeyer Reloading 16 07-11-2013 12:38 PM
Fireforming????? POP Reloading 7 01-11-2010 09:28 AM
Fireforming. Trent The Basics, Starting Out 4 03-31-2008 10:35 PM
no fireforming 338 blygy Rifles, Bullets, Barrels and Ballistics 25 01-27-2008 08:43 AM
fireforming a 6.5-284 moosehunter Reloading 2 02-07-2006 03:44 PM

Current Poll
Do you wear hearing protection while hunting?

All times are GMT -5. The time now is 02:05 PM.


Powered by vBulletin ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Management Powered by vBadvanced CMPS
All content ©2010-2014 Long Range Hunting, LLC