Long Range Hunting Online Magazine


Go Back   Long Range Hunting Online Magazine > Hunting > The Basics, Starting Out


Reply

which base and rings

 
LinkBack Thread Tools Display Modes
  #1  
Old 12-01-2011, 06:15 PM
Bronze Member
 
Join Date: Sep 2011
Posts: 83
which base and rings

I have finally aquired a new rifle ( to me ). I bought a sendero in 25-06. I need to buy mounts and rings. i already have a luepold 4.5-14 bc reticle 1" tube. want something strong. i have looked at the various picatinny rails. i am not familiar with these, so....

will this set up work well for me?

are certain rails much better than others ( i.e., talley vs badger vs ewg etc... )?

what rings or system would you recommend?

gun will be used for deer , varmints and target.
Reply With Quote
  #2  
Old 12-01-2011, 07:04 PM
Gold Member
 
Join Date: May 2009
Posts: 738
Re: which base and rings

Most of the Picatinny rail brands are about the same. The main thing is that you know that a steel rail is stronger and less wear prone than an Aluminium one but it's heavier. So if weight is a factor go Aluminium if you want strength and better return to zero after mount removal go steel.
Badger Ordnance P/N 306-07F Long action, ZERO cant, 5.5 oz. – MSPR: $150 http://badgerordnance.com/base/
, Night force are good rails. Make sure you get the right length rail for the sendero action not a short action rail.
You also need to know that a Weaver rail has narrower recoil slots than a Picatinny rail . Everything else is the same. This means a Weaver scope ring with a recoil bar under it will fit a Weaver rail and a Picatinny rail but a Picatinny scope mount will only fit the Picatinny spec. rail in general. Some over spec Weaver rails will be an exception.

What I would do is install a standard no taper steel Picatinny rail of the right length to the action first . Something like this in a stronger 7075 Al if you want aluminium http://www.midwayusa.com/product/131...00-long-action or something like this in steel http://www.midwayusa.com/product/557...g-action-matte or this http://www.midwayusa.com/product/879...on-matte-steel then buy this mount in either standard no taper for average hunting ranges or whatever MOA taper you need for long range shooting . 20 MOA taper for upto 1000 yards .

MSP Variable Eye Relief Scope Mount and 30mm Rings with MOA: MSP Scope Mounts

Ring inserets for 1 Inch scopes at the bottom of the page and taper or no taper bar selection at the right of the page

With this mount system you can mount a short scope or a long scope and get it in the right eye relief position. It is quick detachable and once you remove it any long range taper is gone with the mount and the long range scope and what is left on the gun is the standard flat steel Picatinny rail that you can mount any kind of Weaver or Picatinny mounts on for any other kind of sight . A short range scope , red dot sight , Halo sight whatever .
You could even have two or more MSP QD variable eye relief mounts one with the long range scope with 20 MOA taper and one with no taper and the short range scope no taper and one with a red dot sight or whatever all quick detachable .
With just the flat rail and a set of low rings on a short range scope the standard stock height may be ok but as the scopes get bigger and you add the higher MSP variable eye relief mount then the stock cheek height ( comb) needs to be higher to support your face. A stock with an adjustable cheek piece is good when you are changing scope heights and mount systems that are all at different heights .
If you stick to one scope height then you can build up the comb height with add on strap on supports off various designs if necessary .
If you look around the MSP site you will see lots of QD track and scope ring options .
Scope mounting is the most difficult part of buying a factory gun in my opinion and it should never be rushed . You should take your time and do a lot of asking , looking and thinking about what you really need before you buy.
Once you have the rifle then you buy the scope you want then you buy a suitable mount system based on the scopes dimentions and then you adapt the stock comb height . It does not work very well in any other order.

Last edited by Bullet bumper; 12-01-2011 at 08:19 PM.
Reply With Quote
  #3  
Old 12-01-2011, 08:02 PM
Platinum Member
 
Join Date: Dec 2001
Location: Potters Hill, NC
Posts: 1,528
Re: which base and rings

sean,
On my .25-06 Sendero I used the Leupold 1-piece Standard LR Scope base in silver (Prod# 521893 - $ 24.99) and Burris 1" Standard Rings, Matte Medium (Prod# 714534 $ 32.99). The Burris Silver rings are prod#557760 $36.99 but are out of stock.
Burris also makes a 1" Signature Ring Pos-Align Offset Insert Kit. Comes with .005, .010 & .020" insert for either aligning up your scope or you can use them to add MOA to your set up. (prod#712472 $14.99).
This setup will allow more than enough MOA for the .25-06. JohnnyK.
Reply With Quote
  #4  
Old 12-01-2011, 08:11 PM
Platinum Member
 
Join Date: Dec 2001
Location: Potters Hill, NC
Posts: 1,528
Re: which base and rings

sean,
Forgot to mention, those items/product #'s are on MidwayUSA. JohnnyK.
Reply With Quote
  #5  
Old 12-01-2011, 08:49 PM
Bronze Member
 
Join Date: Sep 2011
Posts: 83
Re: which base and rings

thanks for all the info. much appreciated
Reply With Quote
  #6  
Old 12-01-2011, 09:04 PM
Platinum Member
 
Join Date: Oct 2005
Location: Michigan
Posts: 2,232
Re: which base and rings

Check out Seekins, I use one of their aluminum 20moa rails and heavy duty aluminum rings on my lightweight 7mm Mag. They work great.

AJ
__________________
If some is good and more is better, then too much is just right.


My mind is a raging torrent, flooded with rivulets of thought, cascading into a waterfall of creative alternatives
Reply With Quote
  #7  
Old 12-01-2011, 09:48 PM
Silver Member
 
Join Date: Jul 2007
Location: Maryland
Posts: 465
Re: which base and rings

Quote:
Originally Posted by AJ Peacock View Post
Check out Seekins, I use one of their aluminum 20moa rails and heavy duty aluminum rings on my lightweight 7mm Mag. They work great.

AJ
+1

They cost a little more but are worth it. If they are in your $ range Badger or Seekins are a buy once cry once investment.
__________________
"Fast is fine accurate is final"
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes


Similar Threads for: which base and rings
Thread Thread Starter Forum Replies Last Post
what base and rings to get...... switchrodeo7 Long Range Scopes and Other Optics 5 07-05-2011 03:06 PM
sold lngrnghunter Optics For Sale 2 03-23-2011 08:54 PM
What rings/base(s)???? Ryan55555 Equipment Discussions 3 12-09-2007 01:12 AM
FS: Leupold MK4 rings / SAKO TRG 42 QD Rings and base / TIKK jfab1165 Guns For Sale 1 03-08-2006 01:15 PM
Need some help on base and rings Long Range Scopes and Other Optics 3 05-20-2004 06:28 PM


All times are GMT -5. The time now is 02:57 AM.


Powered by vBulletin ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Management Powered by vBadvanced CMPS
All content ©2010-2014 Long Range Hunting, LLC