Long Range Hunting Online Magazine


Go Back   Long Range Hunting Online Magazine > Free Classifieds - Buy or Sell > Guns For Sale

Guns For Sale List what you wish but keep it legal.


Reply

DE Rem 700/338 EDGE FS

 
LinkBack Thread Tools Display Modes
  #1  
Old 02-17-2011, 01:36 AM
Platinum Member
 
Join Date: Jun 2003
Location: Hermiston, Oregon
Posts: 2,005
DE Rem 700/338 EDGE FS

I have for sale, a DE Shawn Carlock semi custom built 338 EDGE. Rifle was built in 2007 as my idea of the ulitmate LR packing rifle. It has fulfilled that job nicely, making 4, 1 shot DRT kills on elk at 500,550,700, and 900. 3 were with the 300g SMK at 2800fps (900,700,500) 1 was with the 250g Sierra Gameking at 550. Flat elk hammer!! Rifle is accurate, 1/2-1 MOA is typical w/300g SMK and 88-92g H1000/CCI 250/R-P/3.780" at 2825fps out to 1K laying prone w/bipod. Rings a 15" gong with boring regularity.

Rem 700 stainless BDL action (j-lock,) thats been squared, trued, and lapped.
Remington LSS stock, channel opened up to accept larger diameter bbl
HART 28" stainless/fluted, 1-10 twist, 1 contour under sendero
DE Brake 3 port
Wyatts Extended Mag box (3.780" OAL w/300g SMK)
Factory trigger at a glass like 1.75#
Bedded/floated
Barrel/receiver was bead blasted a grey finish
There is a bit of surface rust that I cant get off from water getting under the bases, cant see it with em on so shouldn't hurt, but It was an elk hunting rifle, I didn't get that particular and take the bases off to clean it after a hunt. You can see it in the pic.

Leupold VXIII, LR/T 6.5-20x50mm, 30mm tube, Side Focus, target knobs, fine duplex, silver finish, missing 1 cap. (leupold will send you one for free, just haven't got around to it) Scope has slight ring marks from the Leupold PRW rings, but scope performs and functions good as new. Butler creek flip open caps included. Small allen wrench included to loosen caps to zero.

Leupold PRW, steel cross slot 2 piece base and 30mm rings (high)

ACI angle indicator
Scope Level
Dewey 36" cleaning rod
3 montana extreme nylon cleaning brushes

39 250g Sierra Gamekings
44 250g Nosler Partitions

RCBS FL die set. Orginally was a 300 RUM set, had them bored out when Shawn was still doing this. Dies work fine, have a bit of surface rust for leaving them in the shop for a winter unkowingly and the seater stem is a bit scuffed up but other then that they load accurate 338 EDGE ammo so I haven't bothered to buy a new set yet. Will throw in the RCBS shellholder as well

I've got 145 Remignton brass as well. 45 pieces I have worked the most with and they have been shot 4-5 times. They are still holding primers. I also have 73 cases have been fired 2x, and 77 cases that have been fired 1x in the 300 RUM barrel that was on before this rifle was rebarreled. It hasnt been sized up or anything.

I have about 275-300 rounds down this barrel. Just gettign good and broke in really. I never abused it, never ever got it hot, cleaned it properly with a bore guide and dewey rod w/jag.

The scope,base,rings are on my 243, the other rifle in pic, which is not for sale, but I"ll be pulling the scope and mounts off for the actual buyer. Prefer not to break up at this time.

I'd like to get $3000 shipped to your FFL, OBO. Not looking for trades. USPS MO or Cashiers Check, or FTF within a couple hundred miles, or meet in the middle on a few hundred mile trip.

PM me with any questions and I'll get back ASAP. Thanks for looking.














Reply With Quote
  #2  
Old 02-17-2011, 01:51 AM
Platinum Member
 
Join Date: Jun 2003
Location: Hermiston, Oregon
Posts: 2,005
Re: DE Rem 700/338 EDGE FS

Forgot 1 thing, Rifle weighs approx 12-12.5 lbs w/scope ready to go.
Reply With Quote
  #3  
Old 02-17-2011, 07:55 PM
Junior Member
 
Join Date: Jan 2009
Posts: 3
Re: DE Rem 700/338 EDGE FS

I am interested in driveing down to take a look and see it shoot with money in hand, plz get back with me.....kain

Quote:
Originally Posted by remingtonman_25_06 View Post
I have for sale, a DE Shawn Carlock semi custom built 338 EDGE. Rifle was built in 2007 as my idea of the ulitmate LR packing rifle. It has fulfilled that job nicely, making 4, 1 shot DRT kills on elk at 500,550,700, and 900. 3 were with the 300g SMK at 2800fps (900,700,500) 1 was with the 250g Sierra Gameking at 550. Flat elk hammer!! Rifle is accurate, 1/2-1 MOA is typical w/300g SMK and 88-92g H1000/CCI 250/R-P/3.780" at 2825fps out to 1K laying prone w/bipod. Rings a 15" gong with boring regularity.

Rem 700 stainless BDL action (j-lock,) thats been squared, trued, and lapped.
Remington LSS stock, channel opened up to accept larger diameter bbl
HART 28" stainless/fluted, 1-10 twist, 1 contour under sendero
DE Brake 3 port
Wyatts Extended Mag box (3.780" OAL w/300g SMK)
Factory trigger at a glass like 1.75#
Bedded/floated
Barrel/receiver was bead blasted a grey finish
There is a bit of surface rust that I cant get off from water getting under the bases, cant see it with em on so shouldn't hurt, but It was an elk hunting rifle, I didn't get that particular and take the bases off to clean it after a hunt. You can see it in the pic.

Leupold VXIII, LR/T 6.5-20x50mm, 30mm tube, Side Focus, target knobs, fine duplex, silver finish, missing 1 cap. (leupold will send you one for free, just haven't got around to it) Scope has slight ring marks from the Leupold PRW rings, but scope performs and functions good as new. Butler creek flip open caps included. Small allen wrench included to loosen caps to zero.

Leupold PRW, steel cross slot 2 piece base and 30mm rings (high)

ACI angle indicator
Scope Level
Dewey 36" cleaning rod
3 montana extreme nylon cleaning brushes

39 250g Sierra Gamekings
44 250g Nosler Partitions

RCBS FL die set. Orginally was a 300 RUM set, had them bored out when Shawn was still doing this. Dies work fine, have a bit of surface rust for leaving them in the shop for a winter unkowingly and the seater stem is a bit scuffed up but other then that they load accurate 338 EDGE ammo so I haven't bothered to buy a new set yet. Will throw in the RCBS shellholder as well

I've got 145 Remignton brass as well. 45 pieces I have worked the most with and they have been shot 4-5 times. They are still holding primers. I also have 73 cases have been fired 2x, and 77 cases that have been fired 1x in the 300 RUM barrel that was on before this rifle was rebarreled. It hasnt been sized up or anything.

I have about 275-300 rounds down this barrel. Just gettign good and broke in really. I never abused it, never ever got it hot, cleaned it properly with a bore guide and dewey rod w/jag.

The scope,base,rings are on my 243, the other rifle in pic, which is not for sale, but I"ll be pulling the scope and mounts off for the actual buyer. Prefer not to break up at this time.

I'd like to get $3000 shipped to your FFL, OBO. Not looking for trades. USPS MO or Cashiers Check, or FTF within a couple hundred miles, or meet in the middle on a few hundred mile trip.

PM me with any questions and I'll get back ASAP. Thanks for looking.














Reply With Quote
  #4  
Old 02-18-2011, 10:19 AM
Platinum Member
 
Join Date: Jun 2003
Location: Hermiston, Oregon
Posts: 2,005
Re: DE Rem 700/338 EDGE FS

PM sent with contact info.

Offers guys? I need to sell this.
Reply With Quote
  #5  
Old 02-19-2011, 06:04 AM
Silver Member
 
Join Date: Mar 2010
Location: Hampton AR
Posts: 362
Re: DE Rem 700/338 EDGE FS

what is bottom $ without scope
Reply With Quote
  #6  
Old 02-22-2011, 03:22 PM
Platinum Member
 
Join Date: Jun 2003
Location: Hermiston, Oregon
Posts: 2,005
Re: DE Rem 700/338 EDGE FS

Rifle, dies, brass, and rod is sold. Am keeping the scope and scope accessories.

Thanks for all interest.
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes


Similar Threads for: DE Rem 700/338 EDGE FS
Thread Thread Starter Forum Replies Last Post
Defensive Edge 338 edge vs Idaho Black bear at 1100 yards lamiglas Long Range Hunting & Shooting 17 01-14-2012 08:50 AM
Defensive Edge - 338 Edge Canyon Rifle Shawn Carlock Guns For Sale 16 05-18-2011 08:50 PM
defensive edge 338 edge shooting session lamiglas Long Range Hunting & Shooting 3 06-20-2010 09:20 PM
.338 edge dies with micrometer top? and other edge related questions locotrician Reloading 4 01-10-2010 11:15 AM
Resizing edge brass on edge dies nddodd Reloading 7 07-28-2009 04:58 AM

Current Poll
I currently have hunting preference points in the following states

All times are GMT -5. The time now is 02:15 PM.


Powered by vBulletin ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Management Powered by vBadvanced CMPS
All content ©2010-2014 Long Range Hunting, LLC