close
Long Range Hunting Online Magazine


Go Back   Long Range Hunting Online Magazine > Rifles, Reloading, Optics, Equipment > Equipment Discussions

Reply

RCBS going Chinese?

LinkBack Thread Tools Display Modes
  #1  
Unread 12-20-2009, 07:24 PM
Bronze Member
 
Join Date: Dec 2009
Location: NJ
Posts: 95
RCBS going Chinese?

I just wanted to share a tidbit of information. I have just purchased a VLD Chamfer Tool for my Case Prep Center, and on the packaging it said that it was made in China. I think that I will be a bit more careful in my purchases in the future.
Reply With Quote
  •   #2  
    Unread 12-20-2009, 11:13 PM
    Silver Member
     
    Join Date: May 2007
    Location: California
    Posts: 458
    Re: RCBS going Chinese?

    What?? Say it isn't so!

    Fred Huntington must be going about 1000 rpms in his grave.
    Reply With Quote

      #3  
    Unread 12-20-2009, 11:52 PM
    Platinum Member
     
    Join Date: May 2001
    Location: Casper Wy
    Posts: 1,379
    Re: RCBS going Chinese?

    Did a quick search and found this....Outdoor Writers - Home
    Kinda makes you feel all warm and fuzzy inside dont it?
    __________________
    "Make everything as simple as possible, but not simpler." -Albert Einstein (1879-1955)
    Reply With Quote
      #4  
    Unread 12-21-2009, 05:28 AM
    Platinum Member
     
    Join Date: Feb 2009
    Posts: 3,546
    Re: RCBS going Chinese?

    If it's China then I'll avoid RCBS components.
    Reply With Quote
      #5  
    Unread 12-23-2009, 01:58 PM
    Gold Member
     
    Join Date: Jan 2007
    Location: North Idaho
    Posts: 668
    Re: RCBS going Chinese?

    They're stuff has been made overseas for several years. All they're electronics are made there. Not sure about their dies though.
    Reply With Quote
      #6  
    Unread 12-23-2009, 06:38 PM
    Platinum Member
     
    Join Date: Feb 2009
    Posts: 3,546
    Re: RCBS going Chinese?

    Only one reason to manufacture in china...cheap real cheap labor. So they saved big time...funny though I didn't see any savings passed on to the consumer...did any of you? So big time profit for them=Greed.

    Greed of coarse and don't believe for a minute it was to remain competitive since most of there competitors aren't in china. ps not capitalizing the C in china wasn't cause I'm dumb.

    At the very least I wouldn't buy their stuff from china and if enough folks followed suit...they might stay in china but they wouldn't be manufacturing in china too long unless they just want to stockpile the stuff and that's not likely.
    Reply With Quote
      #7  
    Unread 12-23-2009, 07:56 PM
    Silver Member
     
    Join Date: Jul 2009
    Location: OZ
    Posts: 362
    Re: RCBS going Chinese?

    Well said!I picked up a set of hornady electric scales the other day only to find made in china on the back,greed greed greed,this is a little bit off topic but to show how extreme it is becoming around the world i was watching a news article which horrified me, it was about beautiful fresh Australian fish being caught here on our shores and then being sent to asia to be cleaned and filleted all because of "labour" cost, WTF!The worst part was this whole process is a 12 week turnaround from when they were caught!!I guess i just can't believe these brands that have built buisness on reputation and earning our trust over decades are willing to throw it all away for a couple of extra dollars.Support your own country i say!!
    Reply With Quote
    Reply

    Bookmarks

    Thread Tools
    Display Modes


    Similar Threads for: RCBS going Chinese?
    Thread Thread Starter Forum Replies Last Post
    Rcbs .308 dies, rcbs primer pocket set, ***SOLD*** patekatek Reloading Equipment and Components 0 07-19-2011 02:09 PM
    Rcbs 750 ejd049 Reloading Equipment and Components 0 06-13-2011 02:54 PM
    RCBS Powder Measure and RCBS Stand newhornet Reloading Equipment and Components 1 04-11-2011 08:41 PM
    rcbs JR 2 camoman80 Reloading 3 09-09-2009 09:20 AM
    Wtt 30rd chinese ak mag for 20rd ak or ar mags EDOGZ818 Gun Parts - Stocks, Barrels, Actions, etc. 0 01-22-2009 08:27 PM


    All times are GMT -5. The time now is 08:52 PM.


    Powered by vBulletin ©2000 - 2017, Jelsoft Enterprises Ltd.
    Content Management Powered by vBadvanced CMPS
    All content ©2010-2015 Long Range Hunting, LLC