Long Range Hunting Online Magazine


Go Back   Long Range Hunting Online Magazine > Rifles, Reloading, Optics, Equipment > Equipment Discussions


Reply

NF 8-32x56 IOR 1913 base Baer rings

 
LinkBack Thread Tools Display Modes
  #1  
Old 04-09-2004, 05:36 AM
Silver Member
 
Join Date: Jun 2003
Location: Aussie in Italy
Posts: 276
NF 8-32x56 IOR 1913 base Baer rings

I just finished putting togeth my scope and set up on my HS HTR.

First off the screws I got with the IOR base were the wrong diameter and thread for the HS reciever.
It took me 2 weeks to get the right ones.
Then they didn't fit the base(I should have thought of this)
So I drilled out the holes in the base.
After that I see that the screws are all 11mm and the length needed is different for each hole in the base since it is tapered.

finally everything was right.
I even found a 30mm steel bar that I could use to settle the rings out with.
I mounted it in the rings and gave it a few taps with a plastic mallet.
After that I took it out and mounted the scope.
Leveled the rifle with a bubble and leveled the crosshairs on a plumb line.

It looks like everything is in perfect order.

So tomorrow I will be spending the day at the range with my new toy, it's been 6 months since I got the rifle, 2 weeks since I got the scope...

As you can appreciate I am pretty keep to get some rounds down the barrel.
I'll be sure to post the results as tomorrow night.

Good shooting to the rest of you for the weekend.
Reply With Quote
  #2  
Old 04-09-2004, 10:15 AM
Platinum Member
 
Join Date: May 2001
Location: Sask. Canada
Posts: 2,410
Re: NF 8-32x56 IOR 1913 base Baer rings

Express,
I expect that several guys on this site are looking forward to hearing how your new HS shoots - we all shared in the decisions that determined your final rifle and scope and have been aware of your patience as things came together.
Best of luck, looking forward to hearing about the bugholes.
Reply With Quote
  #3  
Old 04-09-2004, 01:34 PM
Silver Member
 
Join Date: Jun 2003
Location: Aussie in Italy
Posts: 276
Re: NF 8-32x56 IOR 1913 base Baer rings

One thing I forgot to add was that the IOR base doesn't seem to be quite as well machined as the Les Baer rings.

The finish looks as if it has been sendblasted, a slightly grainy surface.
The thing that had me a little worried was how hard it was to slip the rings onto it.
I had to rap them all the way with a plastic hammer, they just wouldn't slide. I hope that means that they are going to hold together better.

At this stage I have only lock tited the screws in the reciever and base, as I can see no reason to change the base or move it.

I want to do some shooting first, then I will lock tite the ring screws as well, but I want to make sure that it is all square and plumb first.

I have put the scope on fairly loose, not having a torque wrench that means gently tightneing each screw as tight as they will go without getting the idea of forcing any of the screws too much.
I'll be taking a torqx screwdriver to the range just in case ;-)
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes


Similar Threads for: NF 8-32x56 IOR 1913 base Baer rings
Thread Thread Starter Forum Replies Last Post
sold lngrnghunter Optics For Sale 2 03-23-2011 08:54 PM
MilStd 1913 rails NesikaChad Gunsmithing 9 04-07-2010 08:37 PM
New sightron SIII 8-32x56 rings don't clear barrel D.Camilleri Long Range Scopes and Other Optics 12 12-01-2009 03:25 PM
Picatinny 1913 Rail For Montana Action jnoland General Discussion 1 01-07-2008 12:18 AM
FS: Leupold MK4 rings / SAKO TRG 42 QD Rings and base / TIKK jfab1165 Guns For Sale 1 03-08-2006 01:15 PM

Current Poll
I currently have hunting preference points in the following states

All times are GMT -5. The time now is 06:59 AM.


Powered by vBulletin ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Management Powered by vBadvanced CMPS
All content ©2010-2014 Long Range Hunting, LLC