close
Long Range Hunting Online Magazine


Go Back   Long Range Hunting Online Magazine > Chatting and General Stuff > General Discussion

General Discussion Must wear red or OD green socks to participate. I can't see your socks, please be honest.

Reply

How to remove hardened "bedding epoxy"?

LinkBack Thread Tools Display Modes
  #1  
Unread 01-03-2005, 12:19 AM
Silver Member
 
Join Date: May 2004
Location: southeast michigan
Posts: 495
How to remove hardened \"bedding epoxy\"?

Anyone know of a good method and/or solvent for removing what I suspect is "bedding epoxy" inside rifle action...? thanks so much, Larry
Reply With Quote
  •   #2  
    Unread 01-03-2005, 01:55 PM
    Junior Member
     
    Join Date: Apr 2004
    Posts: 29
    Re: How to remove hardened \"bedding epoxy\"?

    Larry.........

    Go to your local hardware store and look for JASCO "premium paint and epoxy remover". It is a great product that has worked well for me in the past. Also MEK will work on some epoxy material. Good Luck
    Reply With Quote

      #3  
    Unread 01-03-2005, 02:56 PM
    Silver Member
     
    Join Date: May 2004
    Location: southeast michigan
    Posts: 495
    Re: How to remove hardened \"bedding epoxy\"?

    David... thanks so much... will give it a try... Larry
    Reply With Quote
      #4  
    Unread 01-03-2005, 08:42 PM
    Bronze Member
     
    Join Date: Oct 2004
    Location: NC
    Posts: 62
    Re: How to remove hardened \"bedding epoxy\"?

    How do you think it would work on a laminated stock? I've got a Rem laminated stock I want to rebed the action. Will it work or will it destroy the stock too?????
    Reply With Quote
      #5  
    Unread 01-04-2005, 12:23 AM
    Silver Member
     
    Join Date: Dec 2004
    Location: BINGHAMTON, NY
    Posts: 166
    Re: How to remove hardened \"bedding epoxy\"?

    a little grinding with dremel or fordom tool would be a better way to go. that stuff will distroy your stock. [img]/ubbthreads/images/graemlins/frown.gif[/img]
    Reply With Quote
      #6  
    Unread 01-04-2005, 12:26 PM
    Writers Guild
     
    Join Date: Jul 2001
    Posts: 1,459
    Re: How to remove hardened \"bedding epoxy\"?

    I reread a couple of times just to make sure. Epoxy inside your rifle action or in your stock?

    For the stock, just get a sanding drum and a dremel tool. Comes out in a flash. Just don't breathe the dust.

    Inside your action, apply a BIT of heat until the epoxy gets soft and 'chisel' out with a piece of wood or stiff plastic.

    Jerry
    Reply With Quote
      #7  
    Unread 01-04-2005, 12:45 PM
    Silver Member
     
    Join Date: May 2004
    Location: southeast michigan
    Posts: 495
    Re: How to remove hardened \"bedding epoxy\"?

    Jerry...thanks for your reply... it turned out not to be epoxy after all... was a combination of grease, dirt, cat hair etc inside the action... rifle was retrieved from a pretty "dirty" room... I think I'm ok... thanks again, Larry
    Reply With Quote
    Reply

    Bookmarks

    Thread Tools
    Display Modes


    Similar Threads for: How to remove hardened "bedding epoxy"?
    Thread Thread Starter Forum Replies Last Post
    How do you remove bedding from a stock? MontanaRifleman Gunsmithing 6 04-18-2011 09:26 PM
    Action bedding with carbon particle epoxy philip140 Gunsmithing 2 01-26-2011 07:27 PM
    NEW! Stocky's Bedding Epoxy Gel from $2 per Rifle, $12.99 Complete Kits Stocky Gunsmithing 0 07-07-2010 02:48 PM
    pilar bedding epoxy bowhunthard Gunsmithing 1 04-07-2009 04:01 PM
    Work hardened brass and POI... jmden Rifles, Bullets, Barrels & Ballistics 18 10-12-2007 06:51 PM


    All times are GMT -5. The time now is 07:08 PM.


    Powered by vBulletin ©2000 - 2017, Jelsoft Enterprises Ltd.
    Content Management Powered by vBadvanced CMPS
    All content ©2010-2015 Long Range Hunting, LLC