close
Long Range Hunting Online Magazine


Go Back   Long Range Hunting Online Magazine > Rifles, Reloading, Optics, Equipment > Rifles, Bullets, Barrels & Ballistics

Rifles, Bullets, Barrels & Ballistics Applied Ballistics

Reply

Yet another barrel breakin/cleaning question...

LinkBack Thread Tools Display Modes
  #1  
Unread 11-10-2010, 10:37 PM
Silver Member
 
Join Date: Aug 2008
Location: Kansas City
Posts: 122
Yet another barrel breakin/cleaning question...

Pardon, but I have not been able to find the answer to this one...

New factory barrel on a Savage 270 WSM

I'd like to follow the common instructions out there to clean after each shot for the first 5 round, then after every five for a while etc....

But when I try to get ALL the color out, I cannot.

I have had this trouble for sometime, with several guns. I use Montana Extreme or Butches Boreshine. I have Dewey's nylon coated rods. I had been useing phospor bronze brushes, but have now tried nylon as well.

The brushes have brass ferrules, as does the rod. I run 20 strokes with the brush, then follow with a soaked patch.

I keep doing this, expecting the patch eventually to come out clean. But it never does.

If I run a second patch, its pretty clean, a third dry patch will be spotless after a couple cycles.

But if I repeat the scrub with a brush (does not seem to matter, nylon or phosphor), I get blue black color on my patch. Even if I have repeated 10 cycles of brush and patch....

I do not have a Borescope.

Are my black patches just from the brass on the rod and the brass wire on the nylon brushes? Or do I have copper still in the barrel?

And if you tell me I still have copper in the barrel, then what kind of OCD, self punishing, saint ever follows these guidelines out there that say to clean out the barrel of all copper after each shot for the first 5-10 shots?????

I mean -- it takes me about 20 minutes to get these guns even "sort of" clean.

I seem to feel that the definition of "clean" is pretty variable....

I want to break this new barrel in "by the books" so that if it does not shoot, I can use it for a boat anchor in good conscience and get a hand lapped Shilen knowing that factory barrels just suck and there is no way around that.....

Thanks In Advance....
Reply With Quote
  •   #2  
    Unread 11-11-2010, 09:18 PM
    Silver Member
     
    Join Date: Jul 2010
    Posts: 420
    Re: Yet another barrel breakin/cleaning question...

    hello. My jag and particulary brushes dissolve in the stronger copper solvents, giving me the false impression the barrel is chalked full of copper. get one of those cheap cleaning kits, the ones that nobody will admit to owning. all aluminum and plastic jags. then reswab and jag, if the problem goes away, it isnt in your barrell. some barrells are a booger to break in. very good bullets like Barnes, in a new barrell that hasnt been burnished by harder bullets can seemingly leave half a bullet in the barrell for every one fired. Hand polished barrells make life easier, but shooting it will do the same thing, just a lot more frustrating
    Reply With Quote

      #3  
    Unread 11-11-2010, 11:11 PM
    Silver Member
     
    Join Date: May 2008
    Location: Texas
    Posts: 151
    Re: Yet another barrel breakin/cleaning question...

    Or try this. Forget barrel break-in, I'm a fan of shooting more and cleaning less. I shoot my barrels until the accuracy falls off then I go and clean them.
    Reply With Quote
      #4  
    Unread 11-12-2010, 08:11 AM
    Platinum Member
     
    Join Date: Nov 2005
    Location: Texas
    Posts: 1,845
    Re: Yet another barrel breakin/cleaning question...

    Try this and then post the results. Works like a charm every time.

    Barrel Break-in
    __________________
    The Truth Is Not Always Good For Business!!
    Reply With Quote
      #5  
    Unread 11-12-2010, 09:24 AM
    Platinum Member
     
    Join Date: Jul 2004
    Location: OHIO
    Posts: 2,417
    Re: Yet another barrel breakin/cleaning question...

    The black is not copper. It is powder fouling that is married to your bore. You need to continue with brushing until the black is gone. There is underlying copper. I also advise leaving a good solvent soaking in the bore for several minutes.

    Speedy's method of cleaning works very well. I've done it.
    __________________
    Derek M.
    Reply With Quote
    Reply

    Bookmarks

    Thread Tools
    Display Modes


    Similar Threads for: Yet another barrel breakin/cleaning question...
    Thread Thread Starter Forum Replies Last Post
    .243 winchester load/barrel breakin 2 part question lefty15 Reloading 3 06-05-2010 03:55 PM
    barrel breakin?? KingJames338Lap General Discussion 3 07-19-2009 09:33 AM
    Barrel Breakin Tbolt Rifles, Bullets, Barrels & Ballistics 8 04-10-2009 10:14 AM
    Barrel breakin tjbill Rifles, Bullets, Barrels & Ballistics 24 03-06-2007 10:32 PM
    7AM Barrel Breakin- part 4 Buffalobob General Discussion 1 09-18-2006 07:44 PM


    All times are GMT -5. The time now is 06:34 PM.


    Powered by vBulletin ©2000 - 2017, Jelsoft Enterprises Ltd.
    Content Management Powered by vBadvanced CMPS
    All content ©2010-2015 Long Range Hunting, LLC