Long Range Hunting Online Magazine


Go Back   Long Range Hunting Online Magazine > Rifles, Reloading, Optics, Equipment > Rifles, Bullets, Barrels & Ballistics

Rifles, Bullets, Barrels & Ballistics Applied Ballistics


Reply

Stringing way to the right...Why?

 
LinkBack Thread Tools Display Modes
  #1  
Old 11-18-2007, 11:53 AM
Silver Member
 
Join Date: Jun 2003
Location: Aussie in Italy
Posts: 304
Stringing way to the right...Why?

I have a Remington 700 Titanium 7mm-08 that is driving mad.
The 2nd shot of a group is always, consistently as far as 3 or 4" to the right, with the average group being around 3MOA. With load it likes I can get 2MOA groups. I would like for it to shoot sub MOA. I've tried everything from 130gn SMKs to 162gn A-Max, 140gn tsx, 140gn Partitions, 160gn b-tips, 140gn b-tips, 140gn failsafes, Federal primers, CCI primers, VVN140, VVN160, H4895, VVN133Öthe list goes onÖ

I bedded the rifle myself, although I can see no faults in the bedding. The barrel is fully floated.
On a gunsmiths' advice the I milled the section of bedding material back closer to the recoil lug. Now it only has about 1" of bedding material forward of the lug.
He reckoned that would solve the problem. BUT IT HASN'T!!!!!

I am %100 sure there are no issues with the scope, rings and bases. The trigger is a Timney with a very crisp, easy half pound pull, scope a Leupold 4.5-14x42, shooting off a pibod and rear bag at a distance of 150 yards.

Iíve just come in from a target session, where I was also shooting with my .300win mag - .46MOA, .308win .200MOA, .204Ruger .25MOA - so it's not me.
This rifle is prone to heating up, but I was waiting a good 5 minutes between each shot, (and it's pretty bloody cold too) without getting out of my seat to ensure the best possible consistency in my shooting technique. The barrel was basically cold for each shot.

Then, just to spite and confuse me, the last group of the session didnít string wide, but high, and so did the next one. The worst part was that it was a very nice group! I measured it at .52MOA. Nothing came even close, the next best group was 1.85MOA. next best was 2.75MOA.
I will try the same load tomorrow and see if it wasnít just a fluke.

I realize this is a lightweight hunting rifle, but I would like to get it down to sub MOA. Next weekend I'll be hunting chamois in the mountains where a 350 yard shot is quite likely to present itself. An 8" to" 14group at the range is just not acceptable.

What can I look at?
I have thought about putting a pressure pad in the front of the stock, but the stock is very flexible in that point and I had to mill out a large gap to ensure it wouldn't come into contact with the barrel.

Since the stringing is consistent, it makes me think that something twisting as the barrel heats up even the slightest amount.

I could get it rebarreled by one smith in the UK who will do the work over a weekend when I go to visit, but that will cost me about $1,200 - without even doing any action work. Otherwise a smith here can do it but it will take at least 9 months and still cost about $900.

Should I try re-bedding? Maybe bed the entire barrel? What else could I check?
Reply With Quote
  #2  
Old 11-18-2007, 06:44 PM
Silver Member
 
Join Date: Oct 2004
Location: california
Posts: 362
i would rebed it. all you will lose is a liitle time i had to rebed a savage that was giving me fits and it fixed the problem

jim
Reply With Quote
  #3  
Old 11-18-2007, 07:45 PM
Platinum Member
 
Join Date: Jul 2004
Location: Texas
Posts: 5,592
Try H 414 and a 120gr blistic tip.

Light weight barrels tend to like lighter bullets.

Start at about 49grs of H 414 and go up 1/2 gr
at a time and use CCI bench rest primers.

This load seems to work on all 7/08's

If this doesent solve the problem then you may
have to use tip pressure. A simple way to find
out if it will respond is to use a 1/2 " wide piece of
cracker box about 2" long placed under the barrel
2" from the muzzle by spreading the stock apart from
the barrel with your hands just enough to insert
the cardboard .

If it changes try 2 pieces, one on top of the other.

Let me know how it works (Good or Bad)

J E CUSTOM
__________________
"PRESS ON"
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes


Similar Threads for: Stringing way to the right...Why?
Thread Thread Starter Forum Replies Last Post
horizontal stringing popwarlick Rifles, Bullets, Barrels & Ballistics 3 03-28-2008 12:22 PM
Stringing shots help swebb38 Rifles, Bullets, Barrels & Ballistics 1 02-11-2008 07:40 AM
Vertical stringing---Causes? hank shaper Long Range Hunting & Shooting 13 02-07-2007 02:05 PM
a cause for horizontal stringing splattermatic Rifles, Bullets, Barrels & Ballistics 7 01-28-2007 09:31 PM
Horizontal Stringing dwm Long Range Hunting & Shooting 22 07-22-2003 08:01 PM


All times are GMT -5. The time now is 02:03 AM.


Powered by vBulletin ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Management Powered by vBadvanced CMPS
All content ©2010-2014 Long Range Hunting, LLC