Long Range Hunting Online Magazine


Go Back   Long Range Hunting Online Magazine > Rifles, Reloading, Optics, Equipment > Rifles, Bullets, Barrels and Ballistics


Reply

SST Barrel Break-in

 
LinkBack Thread Tools Display Modes
  #1  
Old 10-16-2009, 03:20 PM
Silver Member
 
Join Date: Jan 2003
Location: Texas
Posts: 295
SST Barrel Break-in

I'm building a pair of AR-15's with 18" Shilen stainless steel match barrels. The barrels are supposed to get here next Tuesday. Is there a recommended break-in procedure. I used a "fire ten bullets one at a time and clean between rounds" method for my old 700 Remington (.270). Does that hold true for stainless steel?
__________________
Glock Certified Armorer
GSSF Member
Reply With Quote
  #2  
Old 10-17-2009, 05:35 AM
Silver Member
 
Join Date: May 2007
Location: Taranaki New Zealand
Posts: 182
Re: SST Barrel Break-in

Hi Mike, it depends on the finish of the bore. When you "break in" a barrel, you are essentially lapping it with projectiles then cleaning it and polishing it with fine abrasives to remove microscopic burrs to finish the polish.

If you purchased the highest grade barrel offered by the manufacturer, it means that more care was taken to polish the bore before you bought it. In most cases, nothing needs to be done at your end apart from your normal cleaning routine and copper fouling removal as it builds. With lower grade barrels, the bore is rougher and may require a break in using not only copper fouling remover but also an abrasive paste after a given number of shots.

I test and accurize factory rifles on a weekly basis and to be honest, it is quite easy to tell which ones need to be "broken in". I will give you an example of a good bore followed by the worst case scenario.

I purchased an ultra match grade barrel a while back and after the rifle was set up and test loads ready, I went to the range. I fired off something like 12 loads (4 batches of 3 loads), then swabbed the barrel to remove the powder so that I could inspect the muzzle. Looking into the muzzle, there was barely a hint of copper which told me that the bore was giving optimum performance. Furthermore, the rifle grouped in a consistant manner with no big fliers. No need for a break in.

On the latest batch of Howa rifles, the bores have been very rough. This batch has a Hogue stock and is marked Illinois on the barrel. After bedding etc, the rifles need 1-2 fouling shots, then I will get a .250-.3" group, the next group will be around .75", the next group around 1.5". After swabbing the barrel with Hoppes, it is apparent that the fouling is heavy. On inspection of the muzzle, you can see the button chatter marks from manufacturing and the heavy, bright orange copper fouling. These bores have needed a long and harsh break in period and won't come right until a couple of hundred shots have been put through them along with plenty of abrasive hand polishing with Autosol on a jag/rag. (the Howa/WBY Vanguard rifles prior to this were immaculate and did not suffer such problems)

Stainless is not really a heck of a lot different to chrome moly. Both are high carbon, high Chromium steels and both require similar finishing systems. I have a stainless polishing division of our business so this is pretty much up my alley. We also polish many other types of steel inclduding chrome moly. Just remember- each barrel has to be taken on its own merit due to batch variations of the steel and human error during machining and heat treatment. Human error is common and not a problem in itself- nobody is perfect. It only becomes a problem if you are dealing with people who will not concede that mistakes will be made from time to time within the workplace. When that happens, you have no comeback if something really is wrong with the barrel.

Apart from that, its up to how much the consumer can afford with regard to the internal polishing of the barrel as previously mentioned. The less you pay, the more likely it is that you will need to break that sucker in over a long period of time.

Hope that helps.

Last edited by Kiwi Nate; 10-17-2009 at 05:46 AM. Reason: typos
Reply With Quote
  #3  
Old 10-18-2009, 10:24 PM
Silver Member
 
Join Date: Jan 2003
Location: Texas
Posts: 295
Re: SST Barrel Break-in

Thanks for the reply. The barrel started as a Shilen blank so it should be a pretty good barrel. I'll know in a few days. Once I finish the build(s) I'm headed to the range. Thanks again.
__________________
Glock Certified Armorer
GSSF Member
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes


Similar Threads for: SST Barrel Break-in
Thread Thread Starter Forum Replies Last Post
0.5 moa with a 0.177 break barrel! oneholegrouper Rimfire and Airguns 0 01-06-2011 11:37 PM
which break, barrel length, barrel cotour, and twist? nathank Rifles, Bullets, Barrels and Ballistics 1 02-03-2009 08:31 PM
Barrel break-in rufous Rifles, Bullets, Barrels and Ballistics 4 08-12-2007 09:32 AM
BArrel Break in Rifles, Bullets, Barrels and Ballistics 3 05-05-2004 10:56 PM
How to Break in a new barrel, gun nwcook The Basics, Starting Out 3 02-05-2003 01:05 AM

Current Poll
Do You Shoot Rifle Competition?
YES - 33.51%
767 Votes
NO - 66.49%
1,522 Vote
Total Votes: 2,289
You may not vote on this poll.

All times are GMT -5. The time now is 11:33 PM.


Powered by vBulletin ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Management Powered by vBadvanced CMPS
All content ©2010-2014 Long Range Hunting, LLC