Long Range Hunting Online Magazine


Go Back   Long Range Hunting Online Magazine > Rifles, Reloading, Optics, Equipment > Rifles, Bullets, Barrels and Ballistics


Reply

Question about bulk Brass

 
LinkBack Thread Tools Display Modes
  #1  
Old 10-29-2001, 06:28 AM
Silver Member
 
Join Date: Oct 2001
Location: Livonia, MI
Posts: 108
Question about bulk Brass

I have a 338 Lapua. I have been reloading for about 2-3 years but have only used factory brass (factory loads that I have shot in the gun and then kept the brass). I found some un-fired Lapua brass at a gun show and bought 20 pieces. When I got home the brass cycled in the gun fine but would not slide into the RCBS shell holder in my press. Is this common for bulk brass? Do you need to mill the grove deeper on all bulk un-fired brass? Or was this batch bad?

Also do any on you have a line on some reasonably priced Lapua factory ammo. The best I can find in Michigan is $95.00 a box of 20.

Matt
Reply With Quote
  #2  
Old 10-29-2001, 02:26 PM
Silver Member
 
Join Date: Oct 2001
Location: Altus, OK
Posts: 180
Re: Question about bulk Brass

I've bought both the Norma and Lapua brand of 338 Lapua brass. I've never had this problem with new brass. I did buy some supposedly "once" fired brass and a few pieces had the same problem as you have. I have no idea what caused the problem but since I had a couple hundred pieces at that time I just tossed them. For your question on Lapua ammo Graf and Sons used to sell it at around 80-85 a box. Just as a side note the Norma brand lapua brass can be found considerbly cheaper than the Lapua brand (last batch I bought was $129 per 100. And the brass is up to the usual Norma standards of high quality. Hope this info helps.

[ 10-29-2001: Message edited by: 338Lapua ]

[ 10-29-2001: Message edited by: 338Lapua ]
__________________
Learn from others mistakes, you won't live long enough to make them all yourself
Reply With Quote
  #3  
Old 10-30-2001, 07:10 AM
Silver Member
 
Join Date: Oct 2001
Location: Livonia, MI
Posts: 108
Re: Question about bulk Brass

338 Lapua,

Is there any different process to follow when loading "new" unfired brass vs factory load you already shot in the gun. Currently my process is: Clean, neck size/de-prime, trim (if necessary)and deburr, prime, powder, seat bullet.

Thanks for the info on the Norma brass.

Matt
Reply With Quote
  #4  
Old 11-01-2001, 02:33 PM
Silver Member
 
Join Date: Oct 2001
Location: Altus, OK
Posts: 180
Re: Question about bulk Brass

Well, this is what I do for new cases, may be right or wrong but here goes...I first full length resize the cases, trim all cases, debur and chamfer, uniform the flash holes, uniform the primer pockets, then I weigh all of the cases and segregate the over or underweight ones. Then I get the RCBS casemaster and check the contrinceity (SP?) and segregate the ones that are out of round. I don't yet have a neck turner but will be getting one soon to aleive the contrincity problem. Then I primer, charge, and load the bullets. then I will go back to the contricity gauge and check bullet run out, and set the ones with the most run out for sighters. Anyway, that's what I do I'm sure alot of people will disagree with this process but for what it's worth here ya' go. Alot of these process only have to be done once. If need anything else let me know.
__________________
Learn from others mistakes, you won't live long enough to make them all yourself
Reply With Quote
  #5  
Old 11-02-2001, 06:52 AM
Silver Member
 
Join Date: Oct 2001
Location: Livonia, MI
Posts: 108
Re: Question about bulk Brass

338Lapua,

Thanks for the info. That is exactly what I wanted to know.

Matt
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes


Similar Threads for: Question about bulk Brass
Thread Thread Starter Forum Replies Last Post
Quality of Nosler bullets buying in bulk Jinx-) Reloading 9 06-25-2012 07:11 PM
Assorted bulk brass for sale! tillroot1 Reloading Equipment and Components 0 02-27-2011 09:45 PM
WTB .223 bulk bullets krxm21 Reloading Equipment and Components 0 03-31-2009 10:50 PM
Looking for .22 lr CCI velocitor bulk ammunition iggy1965 Other Stuff For Sale 1 01-11-2009 11:40 PM
Factory bulk bullets???? Rifles, Bullets, Barrels and Ballistics 4 06-28-2004 12:49 PM

Current Poll
Do you archery hunt for elk?
YES - 32.06%
67 Votes
NO - 51.20%
107 Votes
Not yet, but I plan to. - 16.75%
35 Votes
Total Votes: 209
You may not vote on this poll.

All times are GMT -5. The time now is 03:12 PM.


Powered by vBulletin ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Management Powered by vBadvanced CMPS
All content ©2010-2014 Long Range Hunting, LLC