Long Range Hunting Online Magazine


Go Back   Long Range Hunting Online Magazine > Rifles, Reloading, Optics, Equipment > Rifles, Bullets, Barrels and Ballistics


Reply

Need ideas for reducing weight of M 700

 
LinkBack Thread Tools Display Modes
  #1  
Old 09-25-2002, 01:31 PM
Silver Member
 
Join Date: Jul 2002
Location: France
Posts: 390
Re: Need ideas for reducing weight of M 700

for hight power silhouette on REM 700 you can

change the shroud for a davidson one in light alloy ( don't forget to lube the thread )or turn the rear of the throud as copy of modification made by Alaskan Gub Work , just need a lathe .

cross drill the firing pin

cut 3 inch of barrel lenght ,to knock down the ram 23 inch is enought for 308 cal .

drill three hole 1/8 in the bolt body ( under face to the magazine ,that help to save a small weight BUT that help to to prevent hot gaz in face if primer piercing )this modification is clone of th ehole you find on Ruger77 bolt .

make a saw mill cut ( 1/8 ) in the bolt handle button

Flutted the bolt

drill three hole ( 1/8 ) in the bolt handle between the bolt body and the bolt end button .

use stamped magazine follower ( ADL parts are stamped , BDL are stainless cast )

I think that enought to be far under the weight limit even if you not done all the modification , shortened the barrel of 2 inch first and make a new crown , rework the bolt shroud and reweight , only with that you are under the weight limit if not enought lightened the bolt handle ....

enjoy metallic silhouette shooting .

DANTEC
__________________
DANTEC
Reply With Quote
  #2  
Old 09-25-2002, 05:08 PM
Silver Member
 
Join Date: Jun 2001
Location: SK. Canada
Posts: 173
Re: Need ideas for reducing weight of M 700

You could loose enough weight if you gave Marvin Pearson an call. He makes custom rings and bases. I have a ring/base set up from him that weighs about 4 ounces at 1.995" in height wiht a 20 moa taper. My combination cost 170.00 which is a lot cheaper than having your gun cut and drilled to death. Fluting the bolt is very drastic and costly and will save you a couple of ounces at best.

I personally would flute the barrel before I started cutting inches off. With the combination of the Davidson bolt shroud over the factory you will save 1.5 ounces. Get Marvins rings and bases and I am sure you will be fine. Marvin's number is 1-360-748-3429. When you call him tell him Troy Glass says you make the best rings and bases for silhouette. I like to plug his product because he does excellent work and is a hell of a nice guy.
Reply With Quote
  #3  
Old 09-25-2002, 09:28 PM
Bronze Member
 
Join Date: Aug 2001
Location: Winnipeg, MB
Posts: 41
Re: Need ideas for reducing weight of M 700

I've heard about those famous Washington rings up here in Canada. I second that advice along with the shroud. I know my way around a mill pretty good and would not think for a second about drilling all those holes in the bolt. Don't cut the barrel either. Keep the weight forward and the ballistic efficiency up, flute the barrel if you must. If you really want a leg up, order one of our M15 Ti titanium actions. It will save you 6 ounces right off the start. I like to plug our own products as well as others fine stuff. [img]images/icons/grin.gif[/img]


Steve
www.prairiegunworks.com
Reply With Quote
  #4  
Old 09-25-2002, 11:05 PM
Silver Member
 
Join Date: Jul 2002
Location: France
Posts: 390
Re: Need ideas for reducing weight of M 700

how much cost one of your titanium action ?

do you shoot silhouette shooting and do you thing you really need 26 inch barrel to get the ram at 500 meters ?

the escape gaz holes drilling in the BODY of the bolt is a safe way to avoid any seriius eyes injury , how you action is design to avoid the need of escape gaz hole in the bolt body ?

good shooting

DANTEC
__________________
DANTEC
Reply With Quote
  #5  
Old 09-25-2002, 11:41 PM
Silver Member
 
Join Date: Oct 2001
Location: Livonia, MI
Posts: 108
Need ideas for reducing weight of M 700

I started shooting Hi-Power Silhouette matches this year. The weight limit is 10 pounds 2 oz. My gun cam in at 10 pounds 5 oz. I had to unscrew the sling studs, pull the magazine spring and plate, and loose the scope caps and sunshield to make weight. This was not a fun experience. My question is what parts can I swap out to lighten up the gun? I have a Rem M 700 VS in 308. It has a Leupold LR one piece base, Leupold rings, and a Nikon 6.5X20 Monarch scope with 4 inch sun shade. I was looking at a comparable Leupold scope and I could save 3.5 oz by going to the VX III 6.5X20 EFR Target. What about bases? The VS comes with a 26 inch barrel. Would it be worth it to have 2 inches removed and have it re crowned? Titanium firing pin? Aftermarket trigger...Jewel or something comperable? I am open to all ideas.

Thanks,

Matt Regalia
Reply With Quote
  #6  
Old 09-26-2002, 05:20 AM
Silver Member
 
Join Date: Oct 2001
Location: Livonia, MI
Posts: 108
Re: Need ideas for reducing weight of M 700

Troy, Thanks for the lead on a lighter rings and base set-up. I will try and give Mr. Pearson a call next week.

As for fluting, what am I looking at price wise to have this done? Any names of places to have it done?

As for needing a 26 inch barrel to take the Ram down. That is what came on the 700 VS. I get 2650 fps with the 168gr Fed Match ammo. I had oridinally bought a PSS (20 or 22 inch barrel) and it did not shoot worth a damn (would not hold under a 1.25 inch group at 100yds with match ammo). I traded it in on the VS and never looked back. Not that the shorter barrel wa the problem, the gun just did not shoot well.

Thanks for all the responses. Keep them coming.

Matt
Reply With Quote
  #7  
Old 09-26-2002, 06:51 AM
Silver Member
 
Join Date: Mar 2002
Location: Southern Illinois
Posts: 397
Re: Need ideas for reducing weight of M 700

I think Steve's onto something. Shroud, rings/bases, are a good start. I wouldn't mess with the barrel unless it's a last resort. Don't mess with your accuracy unless it's broke.

You might consider pulling the barrel & action & milling the barrel channel @ 1/4" wider around the barrel. That'll let the barrel cool faster & take off a few ounces without affecting accuracy. Fluting will cost @ $150, depending on a lot of factors such as barrel length, number of flutes, etc.
You might also look at pulling the buttplate & milling/drilling some 1/2" holes into the buttstock for weight reduction & balance. Of course, your stock will dictate what you can & can't d with it.

Good luck!

[img]images/icons/cool.gif[/img]

[ 09-26-2002: Message edited by: speedbump ]
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes


Similar Threads for: Need ideas for reducing weight of M 700
Thread Thread Starter Forum Replies Last Post
Knox recoil reducing stock 700 bdl la bighornbob Gun Parts - Stocks, Barrels, Actions, etc. 1 11-12-2009 10:18 AM
Ideas for adding weight to a HS stock? KDB Gunsmithing 14 09-25-2009 11:03 AM
Reducing runout suggestion ODAVID Reloading 26 12-26-2008 03:20 PM
Reducing felt recoil Slopeshunter Rifles, Bullets, Barrels and Ballistics 5 11-06-2006 11:19 PM
REcoil reducing stock overbore Equipment Discussions 1 10-21-2006 05:16 AM

Current Poll
Do you archery hunt for elk?
YES - 34.32%
116 Votes
NO - 48.52%
164 Votes
Not yet, but I plan to. - 17.16%
58 Votes
Total Votes: 338
You may not vote on this poll.

All times are GMT -5. The time now is 11:19 PM.


Powered by vBulletin ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Management Powered by vBadvanced CMPS
All content ©2010-2014 Long Range Hunting, LLC