Long Range Hunting Online Magazine


Go Back   Long Range Hunting Online Magazine > Rifles, Reloading, Optics, Equipment > Rifles, Bullets, Barrels and Ballistics


Reply

help for pitted barrel

 
LinkBack Thread Tools Display Modes
  #1  
Old 09-14-2006, 06:33 PM
Silver Member
 
Join Date: Mar 2006
Location: SC
Posts: 215
help for pitted barrel

A friend gave me his rem 700 to clean for him and said it hadn't been cleaned in 15 years. I have cleaned it as far as fouling goes, but the barrel has a very noticible amount of pitting. Is there anything i can do to help this? Maybe tubbs system? Thanks
Reply With Quote
  #2  
Old 09-14-2006, 06:59 PM
Platinum Member
 
Join Date: Jul 2002
Posts: 2,856
Re: help for pitted barrel

the Tubbs system might help a little but if you can see the pitts with the naked eye then they are pretty deep and in order to lapp a barrel enough to remore pitting that bad would loosen the bore up and ruin it worse than it is.

I'd give the Tubbs kit a try , chances are that if he hasen't cleaned it in that long then he probably doesn't shoot it enough to worry about the fouling.

Make sure that you realy clean the hell out of it before you use the kit to get the maximum benifit out of it.
__________________
Si Vis Pacem Parabellum
Molon Labe
Reply With Quote
  #3  
Old 09-14-2006, 07:01 PM
Platinum Member
 
Join Date: Jul 2002
Posts: 2,856
Re: help for pitted barrel

Better yet tell him its ruined and offer to buy it for a $100 , anybody that neglects their weapons like that need to be taken advantage of [img]/ubbthreads/images/graemlins/mad.gif[/img]
__________________
Si Vis Pacem Parabellum
Molon Labe
Reply With Quote
  #4  
Old 09-14-2006, 08:11 PM
Silver Member
 
Join Date: Mar 2006
Location: SC
Posts: 215
Re: help for pitted barrel

you are right, he doesn't shoot it that much. He bow hunts alot. The gun shoots all over the place and he just wanted to see if i could do anything for it. One thing is the barrel was not floated, it had a lot of uneven pressure points in the barrel channel of the wooden stock. I just got it all sanded down and fitted well, just haven't had a chance to shoot it to see if this helped. If it will print in an inch and a half at 100yds he will be happy. I'll try it again tomorrow and see if what i have done helps, if not i'll try the tubbs and if that doesn't work i'll do your suggestion of the $100 [img]/ubbthreads/images/graemlins/wink.gif[/img]
Reply With Quote
  #5  
Old 09-14-2006, 08:56 PM
Platinum Member
 
Join Date: Jul 2002
Posts: 2,856
Re: help for pitted barrel

give it a good once over checking the tighness of ALL the scope ring and mount screws , check the trigger it may need to be adjusted , most 700's can be adjusted down to about 3.5's lbs easly then check the action screw torque they need to be about 50 in lbs (bedding would be a good idea)
and lastly but not least check the crown its amazing how many guys deam their trusty old rifle "worn out" because of a dinged crown.
__________________
Si Vis Pacem Parabellum
Molon Labe
Reply With Quote
  #6  
Old 09-16-2006, 04:28 AM
Gold Member
 
Join Date: Feb 2005
Location: Texas born and raised
Posts: 743
Re: help for pitted barrel

My pop shot an old 03A3 for years killing deer and just about everything else he pulled down on with it. He mostly only shot surplus ball ammo after replacing the bullet with a 150g Sierra spitzer. Average groups were around 2-3" at 100 yds. After he passed on, I got the thing out and decided to see if it would clean up as the tube looked horrific. I spent nearly a day scrubbing and letting it soak then scrubbing some more. After which, I could still see crud in the barrel. I decide that, I really had nothing to loose but the barrel, and ran some J-B paste through on as tight a patch as I could shove through. After doing this several times I followed up with some Sweets, and got some major crud out.

Well since prior to this I was getting clean patches I repeated the process a couple of more times. Each time I got more crud. After about three or four of these rounds, I went back to the standard cleaning solution and then reinspected the thing and it was almost spotless. I let it soak over night with a 2-1 mix of Shooters Choice and some Kroil. The next morning it only took a couple of passes with a brush and a few patches and it was squeeky clean. Now the thing will hold groups around 1/2" at 100. Now this might not be the case with your friends rifle, but if you haven't tried something similar, you might be surprised.

I am sure that the barrel has some undesirable marks through it, but from the way it was, to the way it is now, is like day and night.
__________________
Later,
Mike / Tx

My Photo's

"Heck why would I lie, most folks don't believe the truth when I tell them"
Reply With Quote
  #7  
Old 09-16-2006, 09:33 AM
Silver Member
 
Join Date: Mar 2006
Location: SC
Posts: 215
Re: help for pitted barrel

I just finish shooting, and it shoots a 100% better. I know this will sound funny but i didn't have any J-B paste but i did have some mothers mag wheel polish. It worked great! I was surprised. The can said it would polish all types of metal without scraching, so i said what the heck. It sure cleaned it up and made it nice and shiny. It still is not perfect but much much better. The biggest reason it shoots better is probably because i floated the barrel. I do not know why remington will not free float their wooded stock guns. [img]/ubbthreads/images/graemlins/confused.gif[/img] I have got good clearnce around the barrel all the way up to the lug. It went from a 8" gun to a 1 1/2" gun over night. He will be happy with this! [img]/ubbthreads/images/graemlins/laugh.gif[/img]---Thanks for all the help [img]/ubbthreads/images/graemlins/grin.gif[/img]
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes


Similar Threads for: help for pitted barrel
Thread Thread Starter Forum Replies Last Post
6mm re-barrel brand,length and barrel twist mcseal2 Rifles, Bullets, Barrels and Ballistics 12 11-07-2010 08:14 PM
bolt face pitted due to primer blowout? Wd40 Gunsmithing 14 06-22-2010 07:47 PM
wtb sendero barrel or like custom barrel in 7mm or 30 or 338 mag cal or hevier mayheel Gun Parts - Stocks, Barrels, Actions, etc. 3 02-23-2010 05:18 PM
barrel question. Could a ss barrel be too hard to ream???? oldfamily Rifles, Bullets, Barrels and Ballistics 24 05-29-2009 08:46 AM
which break, barrel length, barrel cotour, and twist? nathank Rifles, Bullets, Barrels and Ballistics 1 02-03-2009 08:31 PM

Current Poll
Do you watch outdoor shows live or by recording them?
Always recorded - 14.11%
102 Votes
Mostly recorded - 24.20%
175 Votes
Sometimes recorded - 13.42%
97 Votes
Rarely or never recorded - 48.27%
349 Votes
Total Votes: 723
You may not vote on this poll.

All times are GMT -5. The time now is 03:29 AM.


Powered by vBulletin ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Management Powered by vBadvanced CMPS
All content ©2010-2014 Long Range Hunting, LLC