Long Range Hunting Online Magazine


Go Back   Long Range Hunting Online Magazine > Rifles, Reloading, Optics, Equipment > Long Range Scopes and Other Optics

Long Range Scopes and Other Optics Nightforce Optics


Reply

scope mounts and rings

 
LinkBack Thread Tools Display Modes
  #1  
Old 04-12-2008, 01:40 PM
Bronze Member
 
Join Date: Feb 2008
Location: Ohio
Posts: 59
scope mounts and rings

I have a nikon 6-18x40mm bdc buckmaster scope to mount on my 700 sps ss 300 remington ultra mag.What is the best rings and mount system out there to keep my scpoe in place and accurate.
Reply With Quote
  #2  
Old 04-12-2008, 04:31 PM
Gold Member
 
Join Date: Dec 2004
Location: Black Hills,South Dakota
Posts: 661
Glens scope hardware is my first choice.

Welcome to Seekins Precision
__________________
The Constitution shall never be construed to prevent the people of the United States who are peaceable citizens from keeping their own arms -Samuel Adams
Reply With Quote
  #3  
Old 04-15-2008, 09:17 AM
Gold Member
 
Join Date: Jan 2008
Location: NW Montana
Posts: 845
Warne maxima steel bases and rings.Mediums would work great.That's what I have on 300 ultra,338 ultra,340 weatherby
Reply With Quote
  #4  
Old 04-15-2008, 09:26 AM
Platinum Member
 
Join Date: Nov 2005
Location: Texas
Posts: 1,844
Just mount them like this and you will never have a problem.


This is the way I do it and the way that it was done by Speedy at SG&Y as we have both found that lock tite fails way too often =

First use steel 000 steel wool and acetone and rough the contact area of the receiver and then do the same to the contact area of the base.

Use a cotton ball with acetone to clean any residual off of the receiver contact area and the base or bases. Set aside the base and be careful not to touch the clean areas. Use a little paste wax on the tip of a toothpick to apply into the threaded areas on the receiver. Apply a very thin layer to the screw threads and to the bottom half of the screw head. Set screws on a clean shop towel -- you get the idea.

Now use JB Weld because it can be heated and removed easier should you want to remove this later on. Mix it and use just a little die if you have it to more closely match the color of the bases and receiver. After mixing on you little piece of cardboard or index card set aside for a few minutes.

Get your propane torch and heat the contact area of the receiver and the contact area of the bases just enough to bring out any moisture that may be present on the surface. When the bases and receiver have cooled back to less than 100 degrees (this will not take long because you did not heat them up that much) using the toothpick that you used to mix the JB put a small amount on the receiver mating surface and on the base mating surface. Don't worry about it oozing now carefully place the bases lining up the screw holes as closely as possible and gingerly set the base on the receiver---immediately place the screws in the holes and get all of them started a few turns.

Now that the screws are started give a turn to one and move to the next screw. Repeat process until they are all snug then tighten each one to its final tension. This is important-----DO NOT OVER TIGHTEN. We do not want all of the epoxy to be completely squeezed out.

Now leave the rifle in the vise and let sit for 5 minutes or so (I use rubber inserts so that the barrel can be clamped in) and get your capful of WD 40, cotton balls and Q-tips. First use dry q tips to remove most of the excess then take a cotton ball and dip a small portion in the WD 40 and very gingerly wipe down the areas you just removed the excess JB. You will notice that it comes of very easy but make sure not to press to hard on the edges where the base and receiver meet we donít want to disturb that line.

Use the q tip or the tip of a toothpick with WD 40 on it to clean out any of the epoxy that migrated through the top of the screw holes an also into the openings of any of the screws.

Now look at the underside of the bases where any excess JB could have migrated into the opening of the receiver or just on top of the receiver for example. Note where a one piece base is used it likes to hide underneath. For this area use the q tip with some WD 40 applied to remove.

Now go off and have lunch about an hour and use the q tips soaked with WD 40 to smooth (gently) the lines where the base and receiver meet. If you have done everything correctly it should look like one piece of metal!!!

In 24 hours or 6 using a light to position over the bases to heat them you are ready to mount your scope.


A final note here make sure to pre fit everything because it will really suck if you find out a base screw is too long and the rifle will not operate!!!
__________________
NRA Life Member And "Low Fencer"
__________________
The Truth Is Not Always Good For Business!!
Reply With Quote
  #5  
Old 04-15-2008, 07:10 PM
Platinum Member
 
Join Date: Jun 2001
Location: Potomac River
Posts: 5,059
Burris Extreme are very good for the price.
__________________
The Smokin Fur Rifle Club
Reply With Quote
  #6  
Old 04-15-2008, 10:08 PM
Silver Member
 
Join Date: Aug 2006
Location: Hatchet City, AB,Canada
Posts: 232
check out www.nearmfg.com as well.. Rock solid...
__________________
Blygy
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes


Similar Threads for: scope mounts and rings
Thread Thread Starter Forum Replies Last Post
Which scope mounts/rings? I have no idea need help!!! matt_3479 Long Range Scopes and Other Optics 3 06-25-2011 11:56 PM
Scope rings and mounts justastooge Long Range Scopes and Other Optics 6 01-03-2010 07:25 AM
Need scope mounts and rings, suggestions? Sako7STW Long Range Scopes and Other Optics 4 11-25-2009 03:26 PM
IOR rings/mounts??? sakofan Long Range Scopes and Other Optics 2 11-24-2003 07:39 PM
Which scope rings and mounts would you use??? Dave King The Basics, Starting Out 9 12-31-2001 08:29 PM


All times are GMT -5. The time now is 01:40 AM.


Powered by vBulletin ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Management Powered by vBadvanced CMPS
All content ©2010-2014 Long Range Hunting, LLC