Long Range Hunting Online Magazine


Go Back   Long Range Hunting Online Magazine > Hunting > PSE TAC 15/15i Crossbow Hunting Forum


Reply

Status of silencing kit for tac15-i?

 
LinkBack Thread Tools Display Modes
  #1  
Old 01-02-2013, 09:36 PM
Junior Member
 
Join Date: Jan 2013
Posts: 2
Status of silencing kit for tac15-i?

Could someone tell me if the silencing kit has been revamped and if so how has it worked out so-far?
Reply With Quote
  #2  
Old 02-17-2013, 11:26 PM
Junior Member
 
Join Date: Feb 2013
Posts: 3
Re: Status of silencing kit for tac15-i?

I'd like to hear about one too
Reply With Quote
  #3  
Old 03-05-2013, 11:34 PM
Silver Member
 
Join Date: Dec 2010
Posts: 391
Re: Status of silencing kit for tac15-i?

Hi Guys,
I'm not the seller or the guy who put these kits together, but I can answer your questions, since I am the guy who did a good bit of the testing on silencing these crossbows.

The short answer is No! The kits have not been modified or changed and the member who was originally selling them has long since sold his PSE crossbow and moved on to another brand

What we did learn was that these materials seemed to work well on certain trigger trigger types, but not on others. I shoot and use these materials on my TAC15i, but on a "Timney" trigger, so I know these work when applied correctly. I can't speak for any other brand of trigger because I can only test what I own and can't comment on those I don't.

It is important that if you should decide to quiet down your crossbow that you make sure that you use a longer piece of material to cover as much of your hammers surface as possible. This means over and around the top of your hammer as well as the length of the striking surface. This nor only provides a better bonding surface, but also insures that you are applying an even amount of build up to all surfaces where a contact with other part can occur.

The company 3M Scotch makes an Outdoor Double Sided Mounting Tape that is sold in 60" x 1" rolls. It has a 5lb. holding strength. This is the adhesive base that is used for the silencing material. It sells for about 5.00 per roll and can be found in some hardware stores.

Next, this is covered with a thin rubberized surface material which is typically used as either rubber pistol grip side plates or also used as the rubberized material for foot plates on wheel chairs.

Personally, I use the pistol grip material which I purchase from Brownells.com. Two grips will produce dozens of strips, if cut with a pair of sharp scissors. The grips sell for about $10. per pair. They are just a very thin rubberized material that is need to protect the foam tape from the hammer contacting the frame pin on each shot. It's the foam tape that absorbs and silences the impacts.

I have about 500 or more shots on the one that I applied and it hasn't moved or worn since I applied it.

Regards,

Xbow755
Reply With Quote
  #4  
Old 03-06-2013, 06:41 AM
Junior Member
 
Join Date: Feb 2013
Posts: 3
Re: Status of silencing kit for tac15-i?

Thanks, I never thought of trying to quiet the hammer itself.
Reply With Quote
  #5  
Old 03-06-2013, 08:29 PM
Junior Member
 
Join Date: Jan 2013
Posts: 2
Re: Status of silencing kit for tac15-i?

Thanks for the info. Been waiting a long time for a reply. I guess it was worth the wait. So nice to have knowledgable people out there to help. Thanks again for your input jon henry.
Reply With Quote
  #6  
Old 03-06-2013, 09:56 PM
Silver Member
 
Join Date: Dec 2010
Posts: 391
Re: Status of silencing kit for tac15-i?

Here are a couple of pictures of how the materials are applied. Hopefully these will explain the exact step-by-steps on how and where to apply your silencing materials.

This is not required on a TAC15 Crossbow due to the fact that a regular TAC15 does not have the frame pin above the trigger assembly, so it does not have the same noise problem.

I also place a very small piece of just the rubberized material on the cable release pad that the hammer strikes to release the crossbows string.

If you are not certain which component I' talking about, please let me know and I'll post a picture of this for you?

Regards,

Jon
Attached Thumbnails - Click to View Larger
Status of silencing kit for tac15-i?-silencing-kit-materials-application-1.jpg   Status of silencing kit for tac15-i?-silencing-kit-materials-aplication-2.jpg  

Status of silencing kit for tac15-i?-silencing-kit-materials-application-3.jpg   Status of silencing kit for tac15-i?-silencing-materials-application-4.jpg  

Reply With Quote
  #7  
Old 03-15-2013, 01:25 PM
Silver Member
 
Join Date: Mar 2012
Posts: 164
Re: Status of silencing kit for tac15-i?

Jon was kind enough to send some material for testing, but I have not installed it.
At the time it was close to hunting season and tearing my crossbow apart when it was shooting so well was not something I was willing to do.

Now the season is over, so I might just give it a try.
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes


Current Poll
Do you archery hunt for elk?
YES - 29.34%
49 Votes
NO - 55.69%
93 Votes
Not yet, but I plan to. - 14.97%
25 Votes
Total Votes: 167
You may not vote on this poll.

All times are GMT -5. The time now is 07:04 AM.


Powered by vBulletin ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Management Powered by vBadvanced CMPS
All content ©2010-2014 Long Range Hunting, LLC