Long Range Hunting Online Magazine


Go Back   Long Range Hunting Online Magazine > Hunting > PSE TAC 15/15i Crossbow Hunting Forum


Reply

Does a TAC 15 (the non-i version) keep its zero when re-assembled?

 
LinkBack Thread Tools Display Modes
  #1  
Old 12-15-2010, 04:51 PM
PUBLISHER
 
Join Date: May 2001
Posts: 5,883
Does a TAC 15 (the non-i version) keep its zero when re-assembled?

The TAC 15 upper attaches to your own AR 15 lower. The TAC 15i version is permanently attached to its own PSE upper.

Mark from NJ just asked me if the "15" version can lose its zero when it is disassembled and then re-attached. I really don't know the answer and I hope one of you can tell me it from your own experience with your TAC 15.
__________________


Long Range Rifles, LLC - Ready To Ship

Components and assembly by LRH Sponsors
Reply With Quote

  #2  
Old 09-21-2011, 12:27 PM
Junior Member
 
Join Date: Sep 2011
Location: indiana
Posts: 19
Re: Does a TAC 15 (the non-i version) keep its zero when re-assembled?

LOL NO you do not loose the zero of your weapon if that was the case i would of been dead in Afghanistan for cleaning my weopon i own a tac 15 and switch barrels to kill ground hogs at 300 yard and then swich back to my xbow and shoot 80yrds dead nuts and thanks for asking......
Quote:
Originally Posted by Len Backus View Post
The TAC 15 upper attaches to your own AR 15 lower. The TAC 15i version is permanently attached to its own PSE upper.

Mark from NJ just asked me if the "15" version can lose its zero when it is disassembled and then re-attached. I really don't know the answer and I hope one of you can tell me it from your own experience with your TAC 15.
Reply With Quote
  #3  
Old 09-23-2011, 07:37 PM
Junior Member
 
Join Date: Sep 2011
Posts: 10
Re: Does a TAC 15 (the non-i version) keep its zero when re-assembled?

But....
I have discovered a very interesting thing with my tac15....I have two ar's...and with the lower from one if I sight it for dead center hits, at say, 50 yards, then switch to the other lower, my point of impact changes about 6 inches. I have switched back and fourth several times, and lower #1 will hit dead center (or as near to dead center as tac-15s will...+- and inch or so), and lower #2 will ALWAYS hit 6 inches low/left.
I'm not sure why this is, but might be because lower #1 is collapsible stock, and lower #2 is fixed stock...that really is the only difference between the two lowers. And yes, I have adjusted for parallax.
Tim
Reply With Quote
  #4  
Old 09-25-2011, 10:12 PM
Junior Member
 
Join Date: Sep 2011
Location: indiana
Posts: 19
Re: Does a TAC 15 (the non-i version) keep its zero when re-assembled?

Tim when i was in the army we all swaped out our lowers in our sqaud all shot same but they were all the same brand stock
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes


Similar Threads for: Does a TAC 15 (the non-i version) keep its zero when re-assembled?
Thread Thread Starter Forum Replies Last Post
DPMS LR.308 A3 Receiver (Assembled) 308-FTT-EA1 CS T Gun Parts - Stocks, Barrels, Actions, etc. 23 10-07-2011 12:49 PM
DPMS LR.308 A3 Receiver (Assembled) CS T Gun Parts - Stocks, Barrels, Actions, etc. 8 07-06-2009 09:10 PM
6mm-06 or AI version info. ? ol mike Reloading 14 06-12-2007 08:57 AM
338 AM assembled, pics.... Fiftydriver Rifles, Bullets, Barrels and Ballistics 140 05-25-2006 08:29 AM
The 300 RUM Improved vs the 338 version Digger49r Rifles, Bullets, Barrels and Ballistics 2 07-07-2003 09:26 AM


All times are GMT -5. The time now is 11:14 PM.


Powered by vBulletin ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Management Powered by vBadvanced CMPS
All content ©2010-2014 Long Range Hunting, LLC